Veneto European Island Range Hood ZI

main_photo

Regular Price : ~~$1,099.00~~

Our Price : $829.00

Charcoal Filter :

Extension :

Shipping :

Size :

Qty : ea

Customer Rating :

Overview

Features

How to Install

Island Part & Install

Wall Part & Install

Veneto® designs range hoods with the consumer firmly in mind, devoting a great deal of time, knowledge and thought to researching and observing people so we can anticipate their needs and wants. The result is products which not only look beautiful but are also easy and more enjoyable to use.

Specifications

Product name	Veneto European Island Range Hood ZI
Model Name	Z Island
Size	30", 36", 42"
Brand	VENETO
Color	Stainless steel
Power Rating	120V / 60Hz (USA & Canada standard)
General Input	278 W (198W + 4 x 20W)
Motor Input Power	198 W
Motor Revolution	600 RPM (±10%) to 1800 RPM (±10%)
Levels Of Speed	6 Levels
Maximum Airflow	900 CFM
Air Pressure	> 160 pa
Noise Level	(dB / sone) Approximately 25 / 0.4 to 56 / 7.0 (Lowest to highest Speed)
Motor Type	Dual Chamber Ultra Quiet
Fan Type	Dual Centrifugal / Sirocco
Control Type	Dual Electronic Control Panels with LCD display
Illumination	20W
Venting Size	6 inch round
Interference Protection	Radio Frequency Interference Protected
All mounting hardware are included for self assembly!!

Characteristics and Benefits

	Fan: These high-capacity fans are easily powerful enough to pull exhaust gases out of a fireplace. Your best bet is to install a range hood that's no bigger than you need.
	Motor: Veneto range hoods are equipped with specially designed Hi-Speed and Ultra Quiet 6 speed motors. The motor revolves to reduce noise and increase CFM.
	Light: Perfect lighting in the cooking area is provided by halogen spotlights fitted in the Veneto range hoods. Flap: Non return flaps prevents cold air and grease vapors from sinking back down through the extractor.

"The European Island Mount Range Hood" has the simple elegance and beautiful Stainless Steel finish which sets it apart from other island mount hood and allows the range hood to be a focal point in the kitchen. This series range hood features a powerful 6 speed motor that provides up to 900 CFM of ventilation. The stylish push button control panel is located at the front of the hood for ease of use.

Demension

Veneto Range Hood Main Body

Main Size

Accesories

Charcoal Filters for ductless venting ($25 extra)
	If external ducting is not practicable, Veneto range hoods can alternatively recirculate the air, and able to cope with even the highest levels of smoke, steam and heat. Charcoal Filter $25.00 + $5.00 shipping if sold separately. Click to see more

Additional Pictures

Veneto's line of range hoods includes a variety selection of sizes, shape, and styles. You can also choose between range hoods that vary in terms of price, style, finish as Veneto manufactures units designed for stylish modern kitchen appliance. Veneto Range Hoods come in an attractive stainless steel finish and slick glass hood for decorative kitchen.

When deciding between Veneto range hoods, check the specifications on your stove top. If your stove has a BTU rating of approximately 50, then you might find an appropriate Veneto Range Hood for under $500, an incredibly competitive price when you consider the reputation of Veneto Range Hoods. Veneto Range Hoods top-of-the line range hoods operate efficiently and look very sharp in modern kitchens.

Veneto range hoods are available as wall-mounted, and Island Mounted range hoods. In addition to providing the best in air replacement or filtration, many of these range hoods come with 20 watts halogen lighting, which gives cooks additional light and adds an appealing touch to your range hood. Most of the Veneto range hoods are structured for 8 to 9 foot ceilings. However, you have the option of purchasing additional ducting or chimney extension to accommodate higher ceilings. The Factory Outlet backs Veneto Range Hoods with a limited one-year warranty.

Charcoal Filter	None
	Charcoal Filter
Extension	None
	9' to 11' Ceiling
Shipping	Standard
	Canada
Size	30inch
	36inch
	42inch
Company	Veneto
Feature	- Mounting style : Island Mounted - 900 CFM dual centrifugal blower - Dual six-speed electronic, touch sensitive control panel with LCD display (both side accessible, EZreach design) - Delayed power auto shut off (programmable 1-15 minutes) - 30 hours cleaning reminder - Four 12V 20W lights (MR-16 type light bulbs) - Three aluminum 6 layers micro-cell washable grease filters (dishwasher-friendly) - Heavy duty 19 gauge 304 (18/8) stainless steel (brushed finish) - Telescopic Arterative chimney of variable dimension - 6" round duct vent exhaust and back draft damper - Venting Mode: Duct (optional charcoal filter available for ductless) - One-year limited factory warranty - Motor Input Power:198W - lighting Power:4x20w - Wind Deal:580-900m3/h - Wind Pressure:>160Pa - Noise:<60dB(A) - Wind Output Diameter:150mm

* Air flappers / Please make right side up to prevent malfunction

How to program

1. Product introduction
Thank you very much for choosing our range hood. Our company has developed a series of range hoods on the basis of assimilating the advantages of high volume of air, lower noise and elegant appearance.

Production Configuration

1	Exhaust pipe	4	One-way valve	7	Lamps
2	Decorative cover	5	Aluminum filters
3	Machine body	6	Bracket for decorative tube

2. Installation and Operation

Position the range hood on the center of cooking stove wall. For best results, the mounting height of the range hood should be 25"-30" (65-75cm) above the top of the range. Mark the position of the holes, which need to be drilled in order to mount the range hood.

* 70cm = 27.59 inch

According to marks, drill two holes appropriate for heavy duty wall anchors and screws（not included）. Mount the range hood on the wall with the two screws and anchors and tighten.

3) Install the one-way valve on top of the range hood and assemble the exhaust pipe and decorative cover.
4) Affix the decorative cover with two M4 tapping screws on the hood body.
5) Make sure all switches are off and then insert the electrical plug into an outlet.
6) Control Panel Layout and Buttons Configurations:

* Button Functions:
Power: Power ON/OFF and auto-shutdown delay timer.
Decrease Value: Blower(motor) speed decrease, timer value increase and cumulative timer reset.
Increase Value: Blower( motor) speed increase timer value increase, and enter timer mode.
Blower Power Indicator: Lights up with blower(motor) is running.
Blower Speed Indicator: Shows current blower(motor) speed.(1-3)
Light Power Indicator: Lights up when lights turned on.
Light: Turns ON/OFF.
Power-on Speed Indicator: Show the speed image.
Power-off Delay Digital Timer: Indicates the length of time left for delay off function.
Power-off Delay Timer Indicator: Lights up when auto-shutdown delay timer function is on. Meanwhile, this button also called Power-on Elapsed Digital Timer, because it indicates the accumulated time the system is running when the Power-off Delay Timer Indicator function not be activated.
*Controls:
*Ajusting the timer function:
While the blower(motor) is running, press and hold Power button over 3 seconds to activate delay off time. The system will ture off automatically in 1 minute.
While the blower(motor)is not running, press and hold Power button over 3 seconds to enter timer mode. Ajust to desired of delay off timer by pressing Increase Value or        Decrease Value button (minimum 1 minute to maximum 15 minutes).Press Power button once to exit timer mode.
*Automatic cleaning reminder:
      When blower(motor) starts to rotate, cumulative running time will be shown iin Power-off Delay Timer Indicator. This timer icon flashes when 30 hours is up and reminds user to clean the aluminum filter.
       After cleaning the filter and when the motor is not in use, press and hold Increase Value button over 3 seconds to reset the timer. Please note that turning off or disconnecting the system will not reset the Power-on Elapsed Digital Timer.
* Ajusting the blower(motor) speed:
       Press Power button once to turn on the system.The Blower Power Indicator flashes showing that the blower(motor) is ready.Press Decrease Value button will decrease the speed of the blower(motor) from 3-1.( strongest to quietest). Press Increase Value button will increase the speed of the blower(motor) from 1-3(quietest to strongest).
      Press Power button once to turn off the system.
        The system saves user configurations, hence settings such as light and blower(motor) speed will remain the same the next time it is turned on.

3. Technical parameters

ITEM	unit	parameter
Rated Voltage	V	220-240
Rated frequency	Hz	50
Motor input power	W	198
Lamp power	W	≤2X20
Air volume	m3/min	9.5~15
Air pressure	Pa	>160
Noise level	dB(A)	<70
Air output diameter	mm	150

4. Maintenance
1) Make sure to pull out the plug and cut off the power before maintenance to ensure your safety.
2) Clean the inside and outside of the range hood with warm water containing neutral detergent, then dry them with a piece of dry cloth. Do not scrub them with rough materials such as cleansing ball to avoid damages to the surface. Put on gloves to avoid injuring your hands when cleaning the inside. The cleaning can be done once half a month to a month.
3) Do not crush the wind wheel when cleaning the inside of the wind track of the wind wheel to avoid the deformation of the wind wheel. Otherwise the movement will be increased, which will result in more noise and influence the effect of absorbing the oil-smoke.
4) Frequent cleaning of the filter shall be done. First press the spring on the edge of the filter to dismantle the filter, dip it into strong detergent and brush its surface with soft brush; then hold the filter with both hands and move it up and down in the detergent, clean it with clean water, after which dry it by airing and install it as what it is as before. The cleaning can be done once a week. Do not clean it with combustible detergent such as banana oil and gasoline.

5. Cautions
1) Do not attempt to install this appliance yourself without appropriate electrical and technical background.
2) When maintaining this range hood or changing a light bulb, please be sure that all power switches are in the off position.
3)Do not let the detergent flow into the electric appliance box and the switches when cleaning the inside of the range hood to avoid leaking electricity.
4)Do not flambe under the range hood.
5)There is a fire risk if cleaning is not carried out according to the instructions.
6) Cut off all the circuits with power before approaching the connection ends.
7)This appliance is not intended for use by young children and infirm persons unless they have been adequately supervised by a responsible person to ensure that they can use the appliance safely。
8) Young children should be supervised to ensure that they do not play with the
9) There should be adequate ventilation of the room when the range hood is used at the same time as appliance burning gas or other fuels.
10) The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas and other fuels.
12) The minimum distance between the supporting surface for the cooking vessels on the hob and the lowest part of the range hood, when the range hood is located above a gas appliance. This distance should be at least 70mm. If the instructions for installation for the gas hob specify a greater distance this has to be taken into account.
13) Regulations concerning the discharge of air have to be fulfilled.
14) Warning：If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or a similarly qualified person in order to avoid a hazard.

INSTALL CHARCOAL FILTER

USE & PROGRAM LED LIGHT

1. Buttons:

: Light
: Motor speed up / timer up / accumulation timer reset
: Motor speed down / timer down / Timer start
: Power

2. Operation

Grease filter washing reminder:

The time showing on LCD screen when the motor is running is the accumulated working time of the motor. After it reaches 30 hours then a reminder icon will be flashing at the right bottom corner, reminding user to wash the filter.
After washing put the filter back on. At the stand by mode, press for over 3 seconds, the accumulation timer will be reset.

Motor Speed Adjust:

Press , the motor icon will be flashing. Four buttons will be lighted on. Pressing decreases motor speed and is for increasing.
Press , power off. The motor stops and all four button lights will be off as well.
The default motor speed is the speed at which the motor was turned off last time.

Timer

When the motor is running, pressing for 3 seconds will start the timer function. The timer will turn the power off after the pre-set time is over.
Under the standby mode, press for 3 seconds, the timer icon will be flashing. Press to reduce time, press to increase time (1-15 mins adjustable)

Light

independently controls lights (ON/OFF).

3. Product Cosmetic Quality Requirements

LCD screen has to be at the same level of the stainless steel surface, common differences allowed: –0.5mm to +1mm
The button is transparent with scripts on top. The printing should not be washed off by any normal chemical washing material.
The light color is blue.
The buttons are (from left to right): Power (), “-“ ( ), “+” () and Light ().

Veneto Island Mount Range Hood Install Guide

Veneto Island Mound Range Hoods
Parts & Installation Guide

Download printer friendly DI specific instructions and safety warnings. (PDF)

1. Parts

* Click this picture for lager one.

1. 6 inch Duct
2. Extension Length 4 PCS
3. Lower Support Frame
4. Upper Support Frame
5. Upper Chimney
6. Lower Chimney

2. Installation

Step 1. Upper Support Frame Set Up

* Click this picture for lager one.

1. Install Wall Expansions (4 pieces) to your ceiling
2. Hang the upper frame to the ceiling.
3. Tighten Wall Expansions.
4. See the order of Rall Expansion parts (see the photo.)
* Black hole of the Upper Support Frame is a duct from the ceiling.

Step 2. Main Body and Lower Support Frame set up

* Click this picture for lager one.

* Attach 2 Air flappers on top of the range hood main body

* Click this picture for lager one.

1. Put the Lower Support Frame on the range hood main body.
2. Put 4 M6*16mm Screws into the holes (4 holes. front side and back side each have 2 holes)
3. Detach the grease filter from the range hood main body.
4. Find 4 screws from #4 and tighten them with nuts.
5. Slide in the Lower Chimney to the main body.
6. Mount 4 Extension Lengths to the Low Support Frame with 8 pcs of M4*12mm screws, each extension should be supported by 2 screws. When you tighten extensions use the lowest holes of each extension.

Step 3. VENETO Island mount DI model glass set up

* Click this picture for lager one.

1. After the Lower Frame is mounted
2. Take out 4 screws from the main body for glass installation
3. Put the glass on the main body
4. Tighten 4 screws on the main body
* This step is only for Veneto Island mount DI model.

Step 4 . Complete installation

* Click this picture for lager one.

1. Slide in the Upper Chimney into the 4 Extention mounted to the main body.
2. Use 8pcs M4*12mm screws to the Upper Chimney to the main body to the extention. Each extension should be supported by 2 screws.
3. Mount the upper chimney to upper frame by using 2 screws which are enclosed with air flappers.
4. Attach the grease cup in to the main body.
5. Peel the films from the chimneys' surfaces.

Veneto Island Range hood part and installation

Veneto Island Range Hood Parts & Installation

* To see the large picture, Click the part list picture

Part Installation

Veneto Wall Mount Range Hood Installation Guide

Veneto Wall Mound Range Hoods
Parts & Installation Guide

Download printer friendly B2W instructions and safety warnings. (PDF)

Download printer friendly DW instructions and safety warnings. (PDF)

1. Parts

* Click this picture for lager one.

1. Range Hood main body
2. 6 Pcs M4*12mm Screw, 1Pc M4*36mm Screw, 2 Pcs M6* 50mm Rall Expansion, Air flapper, Guide Book
1Pc Plastic Expand Chimney
3. 6inch Duct (Alumium Pipe)
4. Bracket, Upper Chimney(with holes), Lower Chimney

2. Installation

* Click this picture for lager one.

1. Draw a horizontal line on the wall and indicate 2 spots for holes for Rall Expansions. Measure the distance between two holes and make holes.
2. Attach 2 Air Flappers on the main body drill.
3. Mount the main body to the wall.
4. Mount the duct to the main body.
5. Mount the Lower Chimney to the main body
6. Mount the Lower Chimney with main body by using 2 Pcs M4*12mm Screw.
7. Put in the Plastic Expand Chimney into the wall for mount Bracket.
8. Mount the Bracket and put in the M4*36mm Screw into the Plastic Expand Chimney.
9. Slide the Upper Chimney into the Lower Chimney.
10. Mount the Upper Chimney with Bracket by using 4 Pcs M4*12mm Screw.
11. Detach the grease filter from the range hood main body and attach the grease cup inside.
12. Peel the films.

Veneto Island Range hood part and installation